Zaphod BeebIebrox: your cable management is a mess, tidy that crap up!
---ElectroMan---: Anyone else OCD and notice the LED strip he put on the diagonal part of the
window was off-kilter?
MKPolarIce: I just bought some led 30cm strips primarily for case modding. They come
with molex connectors on them. I wouldn't bother messing around with all
simonmaersk: You did some of these steps in a very retarded way. For example the molex
connector. WTF was that??? Not to mentiion your horrible cable management
in that case at the end...
Khris Boter: Just bought a 5m reel. Wish me luck! haha.
Mark Woodworth: Nice video, but I think you just demonstrated what NOT to do. When you laid
out the power connector strip, it should have been at the bottom of the
case side, NOT in the middle where it would show. Your wiring layout was a
mess too. But all-in-all you were just showing how to do it, and you did.
HardcoreWL: Holy cable management, batman!
Liam Morrison: I had to check the comments to make sure I wasn't the only one who thought
that the cable management was horrendous. I like the idea and the lights
look cool, but that bad cable management just completely killed it.
Happy tylermovieproducction: It look like! Homemade Alienware area 51! Thank Man! I love alienware so
Mesmer Z: are there any ways for me to put leds in without soldering anything?
Phillip Mulligan: He is choosing this slightly more cumbersome system because it will look
much cleaner free of wire clutter as explained in 8:20. His extra work does
pay off coming time to show this off at the next LAN party/PC modding
contest. Craftmanship and attention to detail is always in style be it PC
modding, custom cars or fine woodworking.
Милош Илић: Good job, sir.
lebulkEnjoy: Your cable management Loks Bad and you should feel Bad ,too
Daryl Norton: I currently have a low voltage system for outdoor lighting. I have 4 100
bulb white christmas light strings that I want to convert to low voltage
and integrate into my 120 Watt Controller or use something else to control
just the christmas lights. The LED lights are just your standard 120V.
Can anybody point me in the right direction? Thanks in advance
Ben Graves: Was the sea at the start quadrophenia?
elmotuz: If you have to but led strips in your computer, but them in the case not on
side panel so you could do proper cable management!
vvittydit: would it be ok to do this with a molex to sata connector?
BSM Prod: Use heat-shrink tubing on the solder joints!
Serr Kocc: wow inside of your case looks terrible
grayzification: can you show how to plug this in?
Dakawan S: Way to not solder properly, class one at best
GamingAndTech: I have the RGB 5050 LED Strip with a sound activated music contoller built
in my case. Get the RBGs if you like changing your lights.
Adrian Ortega: where were you when i ruined my pc with leds lol =( ty tho ive yet to see
such a good guide for leds like and sub :p
Marco Perfetti: WHEN YOU MENTIONED ALCAHOL EVERY ALCAHOLIC TURNED AROUND TO LOOK FOR THE
Girish Harlikal: The red and black wires from LED strip should b connected to which wires
,black or yellow?????????
Anyone help plzzzzzz
MegaWharfedale: To much mucking around, I measured one length and went all the way around
the outer edges on the inside of my pc, job done, time around 2 minutes.
xxkinetikxx: looks like crap
Frank Jackson: You get such a good view of the cable management.
Alan Vangjeli: well those cable make it ugly
Shrikant Raut: Awesome Video, thank you.
Ikaros Melan: I already bought 15 5mm 12v Pre-Wired Pink LEDs from lighthouse leds. now
im pretty ignorant so when i got them, i had no clue what to do. because i
was expecting them to be ready to connect to my computer case but there
just simple wired lights. apparently i have to ground them to make them
work but not understanding. ground them to what?
ratmdex: Great video
Sam Childers: What is the item that the guy is holding at 8:29 and where can i get it?
Ian Holmes: If you want all of these pre-made with either Molex piggy back connectors,
3 pin fan connectors or even now SATA piggyback power connectors then just
message me for the best supplier on Ebay !!
GhostDJ27: good job man it looks awesome
TheRegalRolston: Anyone ever tell you you're the Bob Ross of LED installations?
jaber4life: How to add LEDs: put LEDs in your case
Xtroidable: where can I find/get hold of the cables that wire up all the strips so that
it's one whole circuit powered by one molex?
Marco Perfetti: wow so you mean my dream has come true, now i can finally put WATERPROOF
LEDS' in my toilet bowl and watch my turds flush away happily into the
sewer to be taken care of the water THANK GOD
KiLo Hellfire: NO NO NO NO NO! USE ELECTRICAL TAPE TO HIDE THE WIRES IT WILL BLEND IN WITH
THE CASE YOU IDIOT (ocd at it's finest)
GhostRiot: Good lord, what a mess.
Alexander25C: Wanted to do it for a long time. before i wached your video. just finished.
Zalman MS800. No side panel. Instaled leds on the front of the case. Looks
absolutele amazing. I've done a better job including cable management. thx
anyway 4 ur vid.
josh haigh: anyone got a link for a cable to link the leds
Synthematix: Solder one wire to the chassis ground and yellow wire to molex plugs yellow
Matvey Tihonov: Coooool =)))
Ikaros Melan: What are the colors of LED lights you can add to the computer. can you buy
RecklessWarriorX: NZXT HUE RGB Led Controller Good for Computers!
Lighthouse LEDs: Yes, you could do that.
pushpopLoC909: The PSU itself I'm assuming. No other reason he would use the molex
connector other than that. It's not a stupid question by the way. You learn
new things by asking no matter how 'stupid' one may think it is. :)
WhatTheHuq?: What wires did you use to connect the LED strips with each other?
How to Add LED Lights to a PC / Computer Case4.7
out of 5